The Design of Rice Milling and Screening Systems Uses the DC Motor PID Method

Aulia Adi Cahya, Riky Dwi Puriyanto

Abstract


Rice is one of the staple foods of most Indonesian people, the processing of rice derived from rice plants goes through many stages, one of which is rice milling and sifting. This research aims to make it easier for farmers to do milling and screening, the system will utilize DC motor rotation which is suitable for application in milling and screening, this system also utilizes electrical energy obtained from sunlight so it is more efficient and environmentally friendly. The milling DC motor will use the PID method with a value of P=25, I=50 and D=5 with a setpoint of 250, while the winnowing motor will use a PWM setting of 200 with a voltage of 7.07 V and a motor RPM of 348. This study also has digital scales. which can easily find out the results in units of grams with a maximum capacity of 5,000 grams. The prototype of this rice grinder and sifter has a success rate of testing sensors and motors in the range of 50%, even though the milling results can be said to be less than optimal, the screening results can work according to function, as well as solar panels that can optimally provide power to move the actuators and sensors. sensors in this system.

Keywords


Proportional–Integral–Derivative (PID); PWM; Motor DC; Encoder; Solar Cell; Load Cell; Monitoring Daya

Full Text:

PDF

References


J. Dambe, D. Rukmana, and S. N. Sirajuddin, “Volatility Of Rice Prices In South Sulawesi,” Am. J. Sustain. Agric., vol. 13, no. 2, pp. 55–60, 2019, https://doi.org/10.22587/aejsa.2019.13.2.6.

Y. Hutapea, T. Thamrin, and B. Raharjo, “Efforts to Improve Rice Milling Capacity in Tidal Swamp Agroecosystem in Banyuasin Regency, South Sumatra,” E3S Web Conf., vol. 232, no. 10, p. 03001, 2021, https://doi.org/10.1051/e3sconf/202123203001.

K. A. Adedeji, N. A. Raji, E. O. Oyetunji, and B. Ishola, “Design and fabrication of a motorized rice hulling machine,” J. Mech. Eng. Res., vol. 11, no. 1, pp. 1–10, 2020, https://doi.org/10.5897/JMER2019.0510.

A. R. Bodie, A. C. Micciche, G. G. Atungulu, M. J. Rothrock, and S. C. Ricke, “Current Trends of Rice Milling Byproducts for Agricultural Applications and Alternative Food Production Systems,” Front. Sustain. Food Syst., vol. 3, pp. 1–13, 2019, https://doi.org/10.3389/fsufs.2019.00047.

S. K. Das, A. Adediran, C. R. Kaze, S. M. Mustakim, and N. Leklou, “Production, characteristics, and utilization of rice husk ash in alkali activated materials: An overview of fresh and hardened state properties,” Constr. Build. Mater., vol. 345, p. 128341, 2022, https://doi.org/10.1016/j.conbuildmat.2022.128341.

I. Januarti, Y. Junaidi, and E. Rosana, “The Impact of Using Combine Harvester Technology on Social Economic Conditions of Swamp Rice Farmers and Harvest Workers in South Sumatera,” J. Manaj. dan Agribisnis, vol. 15, no. 3, pp. 299–308, 2018, https://doi.org/10.17358/jma.15.3.299.

E. Mulyana, I. Januarti, F. Syaiful, and D. Damayanthy, “The Identification of Local Wisdom in Lebak Swampland Management (Shallow and Middle Type) and Its Relation on Rice Farmers’ Household Income in Ogan Ilir Regency,” 1st International Conference on Sustainable Agricultural Socio-economics, Agribusiness, and Rural Development (ICSASARD 2021) , vol. 199, no. 5, pp. 151–157, 2021, https://dx.doi.org/10.2991/aebmr.k.211214.021.

A. C. Kumoro et al., “Effect of drying and milling modes on the quality of white rice of an Indonesian long grain rice cultivar,” Acta Sci. Pol. Technol. Aliment., vol. 18, no. 2, pp. 195–203, 2019, https://doi.org/10.17306/J.AFS.2019.0657.

D. Priyambodo and A. T. Nugraha, “Design and Build A Photovoltaic and Vertical Savonious Turbine Power Plant as an Alternative Power Supply to Help Save Energy in Skyscrapers,” J. Electron. Electromed. Eng. Med. Informatics., vol. 3, no. 1, pp. 57–63, 2021, https://doi.org/10.35882/jeeemi.v3i1.9.

H. Soonmin, A. Lomi, E. C. Okoroigwe, and L. R. Urrego, “Investigation of Solar Energy : The Case Study in Malaysia, Indonesia, Colombia, and Nigeria,” International Journal of Renewable Energy Research, vol. 9, no. 1, pp. 86-95, 2019, https://www.ijrer.org/ijrer/index.php/ijrer/article/view/8699.

E. P. Laksana et al., “Potential Usage of Solar Energy as a Renewable Energy Source in Petukangan Utara, South Jakarta,” J. Rekayasa Elektr., vol. 17, no. 4, pp. 212-216, 2021, https://doi.org/10.17529/jre.v17i4.22538.

D. Handaya and R. Fauziah, “Proportional-integral-derivative and linear quadratic regulator control of direct current motor position using multi-turn based on LabView,” J. Robot. Control., vol. 2, no. 4, pp. 332–336, 2021, https://doi.org/10.18196/jrc.24102.

A. F. Bendary and M. M. Ismail, “Battery charge management for hybrid PV/wind/fuel cell with storage battery,” Energy Procedia., vol. 162, pp. 107–116, 2019, https://doi.org/10.1016/j.egypro.2019.04.012.

K. E. Anyaoha and D. L. Zhang, “Transition from fossil-fuel to renewable-energy-based smallholder bioeconomy: Techno-economic analyses of two oil palm production systems,” Chem. Eng. J. Adv., vol. 10, p. 100270, 2022, https://doi.org/10.1016/j.ceja.2022.100270.

R. H. Saputra, A. Sahara, A. M. Miftahul Huda, and M. A. Aegea, “Estimation of Battery Requirements in 600 WP Solar Power Generation Systems,” J. Phys. Conf. Ser., vol. 1807, no. 1, p. 012019, 2021, https://doi.org/10.1088/1742-6596/1807/1/012019.

M. Manfaluthy, A. Pangestu, R. Arif, and L. A. Sanjaya, “Watt peak meter of solar panel,” J. Phys. Conf. Ser., vol. 2019, no. 1, p. 012097, 2021, https://doi.org/10.1088/1742-6596/2019/1/012097.

M. Paul, S. Islam, A. H. Mia, and M. Z. Abedin, “A Design of Intelligent Controller for Direct Current Motor,” International Journal of Advances in Engineering and Management (IJAEM), vol. 4, no. 4, pp. 519–536, 2022, https://ijaem.net/past-issue-volume.php?issueid=41&.

Y. Kakei et al., “Integration of body-mounted ultrasoft organic solar cell on cyborg insects with intact mobility,” npj Flex. Electron., vol. 6, no. 1, pp. 3–6, 2022, https://doi.org/10.1038/s41528-022-00207-2.

P. Hambir, N. Joshi, P. Karande, and A. Kolhe, “Automatic Weighing and Packaging Machine,” Int. Res. J. Eng. Technol., vol. 06, no. 05, pp. 2129–2138, 2019, https://www.irjet.net/volume6-issue05.

C. Sirikun, G. Samseemoung, P. Soni, J. Langkapin, and J. Srinonchat, “A grain yield sensor for yield mapping with local rice combine harvester,” Agric., vol. 11, no. 9, p. 897, 2021, https://doi.org/10.3390/agriculture11090897.




DOI: https://doi.org/10.59247/csol.v1i1.2

Refbacks

  • There are currently no refbacks.


Copyright (c) 2023 Aulia Adi Cahya, Riky Dwi Puriyanto

 

Control Systems and Optimization Letters
ISSN: 2985-6116
Website: https://ejournal.csol.or.id/index.php/csol
Email: alfian_maarif@ieee.org
Publisher: Peneliti Teknologi Teknik Indonesia
Address: Jl. Empu Sedah No. 12, Pringwulung, Condongcatur, Kec. Depok, Kabupaten Sleman, Daerah Istimewa Yogyakarta 55281, Indonesia